一、双组份打胶机的基本操作原理

　　First, the basic operation principle of two component gluing machine

　　1. 固化剂过滤器下端出口及混合器进料处均设有高压球阀，冲胶泄压用，混合器上设有单向针阀，不但使混胶更加均匀，而且防止两种组份互窜。

　　The 1. curing agent, the lower end of the filter and the mixer inlet are all provided with a high pressure ball valve, which is used for punching and releasing pressure. The mixer is provided with one-way needle valve, which not only makes the mixing glue more uniform, but also prevents the two components from channeling each other.

　　2、基料泵、固化剂泵及比例泵均采用特殊的高压柱赛泵，双向等量供料，基料泵由液压系统驱动，固化剂泵由气动马达驱动。二者辅以增压供料压盘，充分保证高黏度流体的满腔输送，基料压入并增高至高压，固化剂压入并增压，再送至比例泵，固化剂的流量由调比机构调节，二种组份同时送入混合器，充分混合后到达挤胶枪。

　　2, base pump, curing agent pump and proportional pump are used special high-pressure cylinder race pump, two-way equal feeding, base pump driven by the hydraulic system, curing agent pump driven by pneumatic motor. The two auxiliary booster feeding pressure plate, and fully guarantee the delivery filled with high viscosity fluid, the base material is pressed in and increased to high pressure, pressure and curing agent into the supercharger, sent to the proportional pump, curing agent flow by adjusting mechanism for adjusting the ratio of two components at the same time, into the mixer after mixing to glue gun.

　　3. 升降系统采用手动转阀控制，两种组份的比例调节，可通过调整滑块在摆动杆上的位置来改变。

　　3. the lifting system is controlled by manual rotary valve, and the proportion adjustment of the two components can be changed by adjusting the position of the slider on the swing bar.

　　4.双组份打胶机液压/气动型主要有基料泵、固化剂泵、比例泵、基料泵升降系统、调比结构、混胶结构、气动系统、液压系统及电气系统组成。

　　4. pairs of hydraulic press / pneumatic type mainly has base pump, curing agent pump, proportional pump, base pump, lifting system, regulating structure, mixing structure, pneumatic system, hydraulic system and electrical system.

　　二、用中空玻璃打胶机时应该注意些什么以及如何操作中空玻璃打胶机

　　Two. What should we pay attention to when using a hollow glass beating machine and how to operate the insulating glass gluing machine?

　　1、混胶或冲枪时，一定要先打开胶嘴控制阀门，然后再打开供胶机，以免压力剧增损坏设备或者出现安全事故。

　　1, mixing glue or gun, must first open plastic mouth control valve, and then open the glue machine, so as to avoid pressure surge, damage to equipment or safety incidents.

　　2、混胶或冲枪(冲洗混胶器、胶嘴)时，建议把机头行走到轨道末端，用接胶板接住胶嘴内放出的胶，以免污染设备。

　　2, mix glue or blunt gun (rinse glue mixer, glue mouth) when, must move head to track end, use glue board to catch the glue that releases inside glue mouth, lest pollute equipment.

　　3、冲枪时先关闭机头上的B胶出胶阀门，关闭B胶泵，然后打开B胶回流阀门，后冲枪，冲洗至出胶口不出黑胶，冲洗才能结束。

　　3, when the gun, first off the nose on the B glue out valve, turn off the B glue pump, and then open the B glue reflux valve, and finally blunt gun, rinse to the glue mouth, no black glue, rinse to finish.

　　4、操作参数设置时，在控制箱pc显示屏上进行，根据须要而选择设定值，不要随意设定，以免控制器发出错误的信息，影响打胶质量或损坏设备。

　　4, the operation parameters are set on the control box PC display screen, according to the need to select the set value, do not arbitrarily set, so as to avoid the controller to send wrong information, affect the quality of glue or damage equipment.

　　5.机头前方检测玻璃开关的光眼上不能有胶，否则误工作。

　　5. front of the nose to detect glass switch, light eye can not have glue, or else work by mistake.

　　本文由双组份打胶机为您提供，乐竞网页版网站官网登入的网站是:https://www.m.peacedoc.com乐竞网页版网站官网登入将以全心全意的热情为您提供更优良的服务，欢迎您的访问!

　　This article is made up of a two component press machine. Our website is: https://www.m.peacedoc.com, we will provide you with better service with your wholehearted enthusiasm, and welcome your visit!