1、混胶或冲枪(冲洗混胶器、胶嘴)时，双组份打胶机建议把机头行走到轨道末端，用接胶板接住胶嘴内放出的胶，以免污染设备。

　　1, mixing glue or gun (Flushing glue mixer, glue mouth), must move the nose to the end of the track, with the rubber plate to catch the glue released from the glue mouth, so as not to pollute the equipment.

　　2、操作参数设置时，在控制箱pc显示屏上进行，根据须要而选择设定值，不要随意设定，以免控制器发出错误的信息，影响打胶质量或损坏设备。

　　2, the operation parameters are set, in the control box PC display screen, according to the need to choose the set value, do not arbitrarily set, so as to avoid the controller send out wrong information, affect the quality of glue or damage equipment.

　　3、混胶或冲枪时，一定要先打开胶嘴控制阀门，然后再打开供胶机，以免压力剧增损坏设备或者出现安全事故。

　　3, mixing glue or gun, must first open the glue mouth to control the valve, and then open the glue machine, so as to avoid the pressure surge, damage equipment or safety accidents.

　　4、打胶时一定要扶好玻璃，避免玻璃脱离定位，影响打胶质量。

　　Must hold the glass 4, glue, glass to avoid the influence from positioning, glue quality.

　　5、冲枪时先关闭机头上的B胶出胶阀门，关闭B胶泵，然后打开B胶回流阀门，后冲枪，冲洗至出胶口不出黑胶，冲洗才能结束。

　　5, when the gun, first off the head of B glue out valve, turn off the B glue pump, and then open the B glue reflux valve, and finally gun, rinse to the glue mouth without black glue, rinse can finish.

　　6.机头电机下面不要有异物，远离电机以免发生危险。

　　The 6. head motor below do not have a foreign body from the motor to avoid danger.

　　7.机头前方检测玻璃开关的光眼上不能有胶，否则误工作。

　　7. light eye detection of glass on the front of the head of the switch can not have glue, or work.

　　8.胶嘴和两侧的刮胶板如胶多时要清理。

　　8. glue scraping plate on both sides of the mouth and a long time to clean up such as glue.

　　9.吸盘上不能放石灰粉，如有胶请清理，如果有的玻璃边缘正好放到吸盘的中心时，可调节吸盘左右移动.

　　9. on the sucker can not put lime powder, if there is glue, please clean, if some glass edge just put into the center of the sucker, can adjust the sucker moving around

　　10.打三玻时要将铝框检测探针缷掉，双玻时在安装上。

　　10. hit three glass to the aluminum frame detection probe off off, when the installation of double glass.

　　安装探针：将探针上的弹簧压到小时探针的前端与胶嘴平齐时固定好。

　　Install the probe: press the spring on the probe to the tip of the probe, and fix it when the nozzle is flush.

　　本文的精彩内容来自双组份打胶机详细内容请点击乐竞网页版网站官网登入的官方网站:https://www.jncsjx.com谢谢您的到来!

　　The wonderful content of this article comes from the two component dispenser, please click on our official website: https://www.jncsjx.com, thank you for coming!